Rules: Difference between revisions

From WLPS Wiki
Jump to navigation Jump to search
m (Wodie moved page Repeaters, bridges and nodes to Rules without leaving a redirect)
 
(25 intermediate revisions by the same user not shown)
Line 1: Line 1:
= Repeaters =
*Tepeximilpa, Mexico City, 438.025 MHz, -5.0 MHz, DPL 432 for FM analog voice, BW 25 KHz. Motorola MTR 2000, 40 Watts, 120 Ah power backup.
*Tepeximilpa, Mexico City 147.390 MHz +600 KHz NAC $293 for P25 Phase 1 voice and data, 167.9 Hz for analog voice, BW 25 KHz. Motorola Quantar 25 Watts, 12 Ah power backup.
*Benito Juárez, Mexico City, 438.050 MHz, -5.0 MHz, DMR CC 1, BW 12.5 KHz, Motorola SLR5100 10 Watts, no power backup.
*Benito Juárez, Mexico City, down-link 146.550 MHz, up-link 433.550 MHz, TPL 167.9 for FM analog voice, 10 Watts, 120 Ah power backup. Itinerant cross band repeater using two mobile radios.
*Altzomoni, Mexico City, 147.240 MHz, +600 KHz, 103.5 Hz for analog voice, DMR CC 1, Fusion DCS 00, BW 25 KHz. Yaesu DR-1X 20 Watts, no power backup. This repeater is hosted and supported by Heliott Zayas.
= PTTLink nodes =
*[http://43852.nodes.pttlink.org:8102/allmon2/index.php PTTLink Node 43852] P25Link Talk Group 2050.
*[http://51410.nodes.pttlink.org:8101/allmon2/index.php PTTLink Node 51410] Benito Juárez, Mexico City, 146.400 MHz, 0.0 KHz, TPL 167.9 Hz.
*[http://51467.nodes.pttlink.org:8101/allmon2/index.php PTTLink Node 51467] Benito Juárez, Mexico City, Experimental.
= Echolink nodes =
*None, as I don’t like appliance operators.
=  IRLP nodes =
*[http://stn5334.ip.irlp.net IRLP Node 5334] Tepeximilpa, Mexico City, 438.025 MHz, -5.0 MHz, DPL 023, BW 25 KHz.
*[http://stn5995.ip.irlp.net IRLP Node 5995] Benito Juárez, Mexico City, 433.650 MHz, TPL 167.9 Hz, BW 25 KHz.
*[http://stn5882.ip.irlp.net IRLP Node 5882] Taxqueña, Mexico City, 433.750 MHz, TPL 167.9 Hz, BW 25 KHz.
=Motorola Wave=
*Astro-P25 Talk Group, bridged to P25Link network.
= HamWAN =
Currently on the market to start setting up a state wide network. Expected to be ready by March 2022.


= My stuff, my rules =
= My stuff, my rules =
Line 46: Line 7:
= Calling another station format =
= Calling another station format =


A user should call another user using the - "called unit from calling unit" format (also known as "hey you - it´s me" format) using calling identifiers as shown above:
A user should call another user using the - '''"called unit from calling unit"''' format (also known as "hey you - it´s me" format) using calling identifiers as shown above:


*“Illinois State Police car 2-5 From IMEA 3”
*“Illinois State Police car 2-5 From IMEA 3”
Line 56: Line 17:
= Rules =
= Rules =


== Legal ==


== Legal ==
My repeaters, bridges and nodes maintain and operates high-quality, wide-coverage area for the use of all amateur radio operators. Operation and use of these shall comply fully with:
My repeaters, bridges and nodes maintain and operates high-quality, wide-coverage area for the use of all amateur radio operators. Operation and use of these shall comply fully with:
*US Amateur Radio Service (Part 97) regulations of the Federal Communication's Private Radio Service.
*US Amateur Radio Service (Part 97) regulations of the Federal Communication's Private Radio Service.
Line 63: Line 24:


== Operational ==
== Operational ==
*My repeaters, bridges and nodes are provided for the purposes of contacting and passing information between fellow amateur radio operators, and providing service to the public as a voluntary, non-commercial communication service, research and development, and particularly with respect to providing emergency communications when comercial services are not available. If you can reach 911 go that way.
*In the spirit of Amateur Radio Service, users shall respect and support each other in a courteous and positive manner. Due to the wide coverage of the repeater system operators should always pause a minimum of three seconds before transmitting, to allow another station to break in.
*Due to the number of repeaters and/or nodes on-line, key your microphone two seconds before talking to let those systems start.


*Operators shall announce their call sign before transmitting any touch-tone commands, at the end of each communication, and every ten minutes or less during a communication.
* My repeaters, bridges and nodes are provided for the purposes of contacting and passing information between fellow amateur radio operators, and providing service to the public as a voluntary, non-commercial communication service, research and development, and particularly with respect to providing emergency communications when comercial services are not available. '''If you can reach 911 go that way! '''


*There shall be absolutely no communications containing obscene, indecent, or profane words, language, or meaning. Discussion of religion, political or potentially sensitive social issues shall be avoided.
* In the spirit of Amateur Radio Service, users shall respect and support each other in a courteous and positive manner. Due to the wide coverage of the repeater system operators should always pause a minimum of three seconds before transmitting, to allow another station to break in.


*For digital systems as DMR, NXDN and P25, you must have your 7-digit ID will be according to the DMR-MARC/TRBO-6/NorCal/DCI/NC-PRN scheme. [[http://www.radioid.net You can apply here]].
* Operators shall announce their call sign before transmitting any touch-tone commands, at the end of each communication, and every ten minutes or less during a communication.


*Be sure also to DISABLE the ARS!!! ARS is not permitted on DMR. We do not allow GPS positions to be beaconed over the ENTIRE network every 30 seconds.
* There shall be absolutely no communications containing obscene, indecent, or profane words, language, or meaning. Discussion of religion, political, racism, or potentially sensitive social issues shall be avoided. Music, annoying tones, screams, un mature behavior is not allowed.


*For digital repeaters, see my Talk Groups list. Using not listed Talk Groups is forbidden.
* For digital repeaters, see my Talk Groups list. Using not listed Talk Groups is forbidden. I will stun your radio.


*For DMR-MARC talk groups you must also follow the DMR-MARC rules.
For digital systems as DMR, NXDN, P25 TETRA, etc, you must have your 7-digit ID will be according to each system scheme.
For digital repeaters, see my Talk Groups list. Using not listed Talk Groups is forbidden.
For DMR-MARC talk groups you must also follow the DMR-MARC rules.
For BrandMeister talk groups you must also follow the BrandMeister rules.
For DMR+ talk groups you must also follow the DMR+ rules.
For P25Link talk groups you must also follow the P25Link rules.
For TETRA PTTlink talk groups you must also follow the TETRA PTTLink rules.


*For DMR+ talk groups you must also follow the DMR+ rules.
No one shall cause or condone the malicious or intentional interference of anyone's communications on the repeaters, bridges or nodes.
Users shall not communicate with, or discuss the actions of, anyone who violates these rules.


*No one shall cause or condone the malicious or intentional interference of anyone's communications on the repeaters, bridges or nodes.
* No one shall cause or condone the malicious or intentional interference of anyone's communications on the repeaters, bridges or nodes.


*Users shall not communicate with, or discuss the actions of, anyone who violates these rules.
* Users shall not communicate with, or discuss the actions of, anyone who violates these rules.


I will turn off a repeater, bridge or node to terminate improper operation. No warnings or explanations, you are supposed to know the rules if you are using my systems.
I will turn off a repeater, bridge or node to terminate improper operation. No warnings or explanations, you are supposed to know the rules if you are using my systems.


*Control of node connections is normally restricted. Visitors should e-mail me (km4nno at yahoo.com) to gain access codes for the phone patch, PTTLink, IRLP or Echolink nodes they want to connect to other reflectors or nodes. The gateway to the reflectors is open to hams to talk to whoever they hear.
* Some IDs, nodes and reflectors are black-listed, period. Please do not contact me to white-list them as I will never do. Their owners/admins been rude with me, those are the consequences.


*Some IDs, nodes and experimental reflectors are black-listed, please do not contact me to white-list them. I will never do. Their owners/admins been rude with me with no reason, those are the consequences.
* If your node is connected to one of my nodes, there must be NO (as in zero) repeater hang time allowed to pass through to PTTLink, IRLP nor anything resembling a courtesy tone. This means set it to zero, not 500ms or even 100ms. If you are using a keyed CTCSS approach to solving this problem, make sure your tone encoder/decoder combination drops as fast as possible. No repeater IDs or controller messages are allowed at all, unless they are under a user transmission.


*If your node is connected to one of my nodes, there must be NO (as in zero) repeater hang time allowed to pass through to PTTLink, IRLP, or Echolink, nor anything resembling a courtesy tone. This means set it to zero, not 500ms or even 100ms. If you are using a keyed CTCSS approach to solving this problem, make sure your tone encoder/decoder combination drops as fast as possible. No repeater IDs or controller messages are allowed at all, unless they are under a user transmission.
* No nets and no announcements are allowed.


*Cross-links are only acceptable with a written permission from me. Please contact me before making any test or connection or you will be black-listed forever.
* Cross-links are strictly forbidden. If I catch you (and I am a good one in that matter), you will be black-listed forever.


*Please advise your users to disconnect your node if a local conversation becomes extended. Short local greetings are okay while connected, but do not tie up my nodes with a 10 minute local QSO or worst, one hour.
* Please disconnect nodes if a local conversation becomes extended. Short local greetings are okay while connected, but do not tie up my nodes with a more than 10 minutes local QSO or worst, hours.


= Always use high power on portables =
= Always use High Power on portables =


Use high power in portables. The city is not a flat field with no obstructions. Spend some money on batteries and do not live trying to save your only battery, that only keep you making noise on the repeaters. If even with high power you can not reach my repeaters or nodes, try a better location, a better antenna and or a better radio.
'''Use High Power in portables.''' Mexico City is not a flat field with no obstructions. Spend some money on batteries and do not live trying to save your only battery, that only keep you making noise on my repeaters. If even with High Power you can not reach my repeaters or nodes, try a better location, a better antenna and/or a better radio, Baofengs are crap!


= Support and donations =
= Support and donations =


Sorry, no support. I will not help you to program your radio or setup your system, there is plenty information in the libraries and on the internet. Yes this is the way I was taught by old amateur radio farts, now is time to pay them back.
Sorry, no support to others. I will not help you to program your radio or setup your system, there is plenty information in libraries, books, manuals and on the Internet. Learn by yourself. Why? Because this is the way I was taught by old amateur radio farts, now is time to pay them back.


I do not accept donations, etc. When people makes any kind of donation, they thinking they are the new owners of my stuff, They want to rule and control it, so forget about it. Invest on your own.
I do not accept any help, contributions, donations, etc. When people makes any of these, they thinking they are the new owners of my stuff. They want to rule, take decisions and have control over it, so forget about it. Invest on your own hardware.

Latest revision as of 14:55, 10 April 2023

My stuff, my rules

Here you will find the rules and policies for using my repeaters, bridges and nodes. If you do not follow them, you will be blacklisted. That simple.

As the owner, I reserve the right to forbid the use of any repeaters, bridges, remote bases or voice over internet protocol by anyone who repeatedly violates these rules, or anyone who facilitates or encourages others to violate these rules.

Calling another station format

A user should call another user using the - "called unit from calling unit" format (also known as "hey you - it´s me" format) using calling identifiers as shown above:

  • “Illinois State Police car 2-5 From IMEA 3”

Followed by:

  • “IMEA 3 From Illinois State Police car 2-5, go ahead”

Rules

Legal

My repeaters, bridges and nodes maintain and operates high-quality, wide-coverage area for the use of all amateur radio operators. Operation and use of these shall comply fully with:

  • US Amateur Radio Service (Part 97) regulations of the Federal Communication's Private Radio Service.
  • Mexico IFT Ley Federal de Telecomuncaciones y Radiodifusión published on July 14, 2014.

Operational

  • My repeaters, bridges and nodes are provided for the purposes of contacting and passing information between fellow amateur radio operators, and providing service to the public as a voluntary, non-commercial communication service, research and development, and particularly with respect to providing emergency communications when comercial services are not available. If you can reach 911 go that way!
  • In the spirit of Amateur Radio Service, users shall respect and support each other in a courteous and positive manner. Due to the wide coverage of the repeater system operators should always pause a minimum of three seconds before transmitting, to allow another station to break in.
  • Operators shall announce their call sign before transmitting any touch-tone commands, at the end of each communication, and every ten minutes or less during a communication.
  • There shall be absolutely no communications containing obscene, indecent, or profane words, language, or meaning. Discussion of religion, political, racism, or potentially sensitive social issues shall be avoided. Music, annoying tones, screams, un mature behavior is not allowed.
  • For digital repeaters, see my Talk Groups list. Using not listed Talk Groups is forbidden. I will stun your radio.

For digital systems as DMR, NXDN, P25 TETRA, etc, you must have your 7-digit ID will be according to each system scheme. For digital repeaters, see my Talk Groups list. Using not listed Talk Groups is forbidden. For DMR-MARC talk groups you must also follow the DMR-MARC rules. For BrandMeister talk groups you must also follow the BrandMeister rules. For DMR+ talk groups you must also follow the DMR+ rules. For P25Link talk groups you must also follow the P25Link rules. For TETRA PTTlink talk groups you must also follow the TETRA PTTLink rules.

No one shall cause or condone the malicious or intentional interference of anyone's communications on the repeaters, bridges or nodes. Users shall not communicate with, or discuss the actions of, anyone who violates these rules.

  • No one shall cause or condone the malicious or intentional interference of anyone's communications on the repeaters, bridges or nodes.
  • Users shall not communicate with, or discuss the actions of, anyone who violates these rules.

I will turn off a repeater, bridge or node to terminate improper operation. No warnings or explanations, you are supposed to know the rules if you are using my systems.

  • Some IDs, nodes and reflectors are black-listed, period. Please do not contact me to white-list them as I will never do. Their owners/admins been rude with me, those are the consequences.
  • If your node is connected to one of my nodes, there must be NO (as in zero) repeater hang time allowed to pass through to PTTLink, IRLP nor anything resembling a courtesy tone. This means set it to zero, not 500ms or even 100ms. If you are using a keyed CTCSS approach to solving this problem, make sure your tone encoder/decoder combination drops as fast as possible. No repeater IDs or controller messages are allowed at all, unless they are under a user transmission.
  • No nets and no announcements are allowed.
  • Cross-links are strictly forbidden. If I catch you (and I am a good one in that matter), you will be black-listed forever.
  • Please disconnect nodes if a local conversation becomes extended. Short local greetings are okay while connected, but do not tie up my nodes with a more than 10 minutes local QSO or worst, hours.

Always use High Power on portables

Use High Power in portables. Mexico City is not a flat field with no obstructions. Spend some money on batteries and do not live trying to save your only battery, that only keep you making noise on my repeaters. If even with High Power you can not reach my repeaters or nodes, try a better location, a better antenna and/or a better radio, Baofengs are crap!

Support and donations

Sorry, no support to others. I will not help you to program your radio or setup your system, there is plenty information in libraries, books, manuals and on the Internet. Learn by yourself. Why? Because this is the way I was taught by old amateur radio farts, now is time to pay them back.

I do not accept any help, contributions, donations, etc. When people makes any of these, they thinking they are the new owners of my stuff. They want to rule, take decisions and have control over it, so forget about it. Invest on your own hardware.