Mo-Sys StarTracker: Difference between revisions

From WLPS Wiki
Jump to navigation Jump to search
Line 113: Line 113:


== Network ==
== Network ==
Please reboot after any changes on this menu.
* Connection - Set for Static or Dynamic IP.
* APPLY - Apply settings (you need to reboot unit).
* Static IP - This system IP address.
* Netmask - This system netmask.
* Use Gateway - Enable/Disable gateway address to talk to the Internet.
* Gateway IP - Gateway address for Internet conectivity.
* Reconect -
* Set on boot -
* Interface - Selects the interface to configure on this menu.
:eth0 is the Ethernet port.
:eth64 is the IP camera communications port.
[[File:data_network.jpeg|none|800x600]]
[[File:data_network.jpeg|none|800x600]]



Revision as of 17:53, 25 March 2021

Main

Alg

Calib

Mapping

Data

Output

  • Sync Type - Select your GenLock Input signal, Black Burst, TriSync and SDI are accepted, but in SD format, HD is NOT SUPPORTED.
  • Test Data - Select diferent test patters of data set via network.
  • F4 Lens - Turn On if using DigiLens, this option also shows in Lens Data sub menu.
  • Encoder Lens Input only shows which lens encoder is selected on Input sub menu.
  • Serial Out - Enables MoSys serial output if not using ethernet option.

Unicast

  • Destination IP 1, 2, 3 - Set the input to send unicast UDP data.
  • Port 1, 2, 3 - Selects the UDP port number.
  • Protocol 1, 2, 3 - Select the protocol to be sent to each unicast address.
  • Send UDP 1, 2, 3 - Enable/Disable the unicast data output.
  • Ping 1, 2, 3 - send a ping to a Destination Address.

Broadcast

  • BC Port - Selects the UDP broadcast port number.
  • BC Protocol - Select the protocol to be sent to the broadcast address.
  • Broadcast - Enable/Disable the broadcast data output.
800x600
800x600

Input

  • Via Serial Lens - Select the input mode for lens data (Focus & Zoom).
STM - External MoSys encoders.
  • Serial Log - open a console log window.
  • Via UDP - Enable/Disable UDP data input.
  • UDP Port - Select the input UDP port.
  • 4 Axes -
  • Fuse Enc -
  • Enc Only -

The screen also display information about

  • External encoders X, Y, H, Pan, Tilt & Roll.
  • Lens Focus & Zoom encoders.
  • GenLock input signal type/status.
800x600
800x600

Record

  • Jam -
  • IP Source Output -
  • Master Mode -
  • DropFrame -
  • TC Offset -
  • TC Drift - Display
  • Half Rate -
  • Odd/Even - Select the field for
  • Test Jam -
  • Record -

Status information display.

800x600
800x600

Lens Data

  • Enable - Turn On if using DigiLens.
  • Type - Select Wheels if using external encoders.
  • Load File - Only apply for Digilens.
  • Extender - Loads the Extender Menu.
For external encoders, only set the extender X factor.
Load Lens file only for DigiLens.
  • Reverse Encoders - Invert the encoders direction for Focus or Zoom.
  • Reverse Lens File - Invert the encoders direction for DigiLens Focus or Zoom.
800x600
800x600

Network

Please reboot after any changes on this menu.

  • Connection - Set for Static or Dynamic IP.
  • APPLY - Apply settings (you need to reboot unit).
  • Static IP - This system IP address.
  • Netmask - This system netmask.
  • Use Gateway - Enable/Disable gateway address to talk to the Internet.
  • Gateway IP - Gateway address for Internet conectivity.
  • Reconect -
  • Set on boot -
  • Interface - Selects the interface to configure on this menu.
eth0 is the Ethernet port.
eth64 is the IP camera communications port.
800x600
800x600

Advanced

  • F4 Status - On to send data to D3.
  • F4 ST ID - On to be read properly on D3.
  • Serial IO - Must be On for Gen Lock and Lens Encoders.
  • Use IMU - Need to be on, so IR camera works.
800x600
800x600

Tunning