Beginners Guide ASL-AsteriskNG

From WLPS Wiki
Revision as of 04:04, 31 December 2020 by Wodie (talk | contribs)
Jump to navigation Jump to search

PTTLink for beginners.

The first step is to create an account.

Go to https://PTTLink.org/ and click the <Sign Up> link.

File:Asl site menu.png
File:Asl site login.png

Download PTTLink image file

While you are awaiting the verification of your account (usually within 24 hours) you may download one of the image files for you computer system you will use to run your PTTLink node.

Go to wiki.PTTLink.org scroll down to the Downloads section and select the appropriate image for the type of system you will use.

File:Asl download.png

Write the image file to media. Either a USB memory stick, CD or DVD, or a microSD card (Raspberry Pi).

Login to your account

You will need to login to your account at https://PTTLink.org/

File:Asl site menu.png

Click on <Login/Sign Up> as shown in the image above.

File:Asl login.png

Create a Server

You will need to create a "server" : Click on <Portal> then <Server Settings>.

File:Asl server1.png

Click on <Add a new server>.

Please take the time to read the instructions on each page.

Then click <Proceed with Server Setup> if needed.

Fill in all of the information and click <Submit> at the bottom of the page.

File:Asl server settings.png

Request a Node number

At the top of the page, click <Portal> and then on <Node Settings>.

File:Asl node.png

Then click <Request a new node number>.

File:Asl request node.png

Select which server you would wish to have a node number assigned to

if you need more than one node number for the same server, repeat this process

A comment of 'additional node on same server' would be appropriate

File:Asl request node2.png

Once your node number request(s) are processed you will receive an email.

Edit Node settings

Log into your account on https://PTTLink.org/

Click <Portal> then <Node settings>.

The PTTLink node numbers that have been assigned to you are displayed here.

Select which node you wish to view/edit.

Fill in the information for you node and click <Submit>.

File:Asl node settings.png

Write down your node number, password and the call sign you assigned for the node as you will use them to configure your PTTLink system.

Install and configure ASL to your computer

Consult your owners manual or your favorite internet search engine for how to install an image for your computer system.

Install the PTTLink disk image to your computer. Insert the appropriate media for your system and boot the computer.

When the login prompt appears enter the user ID of repeater and press <Enter>.

Enter the default password of allstarlink

Follow the on screen instructions for the initial password change.

For users familiar with the linux operation system you may proceed to edit the system manually.

For users not familiar with linux and ASL, at the Linux CLI (command line interface)

Type sudo asl-menu as the example below shows.

repeater@repeater:~$ sudo asl-menu

This will load the PTTLink configuration menu.

File:Asl menu 1.png

PTTLink software setup

Choose option <1>.

File:Asl first time.png

Cause it is your first time setup, answer <Yes> so you can setup a "root" password. Don't forget to write down your user and password.

File:Asl enter new unix password.png

Setup now will ask if you want to change "repeater" account password with you should already changed at first time login so answer <No>, unless you want to change it again. Do not forget to write it down.

File:Asl repeater pswrd prompt.png

Now lets set time zone <Ok>.

File:Asl timezone setup.png

Choose the node's continent.

File:Asl geo area.png

Choose the node's city.

File:Asl time zone.png

Next you can change the name of you host name, the default is repeater.

File:Asl by default.png

Answer <Yes> to be able to make changes.

File:Asl existing hostname prompt.png

Type the new host name and hit <Enter>.

File:Asl hostname.png

If you want to set up a domain, type it and hit <Enter>.

File:Asl domainname.png

Say <Ok> to this message.

File:Asl existing hostname.png

Now you can make your network settings <Ok>.

File:Asl setting for dhcp.png

Just say <Ok> to this message.

File:Asl you can network.png

To choose between DHCP or Static IP say <Yes>.

File:Asl network setup.png

Use <D> for DHCP or <S>. for Static, if you choose Static, you will be asked to enter it next, for this example DHCP is in use.

File:Asl dhcp or static.png

Just say <Ok> to this message.

File:Asl commented out.png

Just say <Ok> to this message.

File:Asl you can configure.png

Just say <Ok> to this message.

File:Asl importing the.png

Choose option <A1>.

File:Asl a menu a1.png

Choose option <N1>.

File:Asl n menu n1.png

Type the node number for your node. Yes the one you previously wrote down from PTTLink site.

File:Asl node number prompt.png

Choose option <N2>.

File:Asl n menu n2.png

Type the node password for your node. Yes the one you previously wrote down from PTTLink site.

File:Asl node password prompt.png

Choose option <N3>.

File:Asl n menu n3.png

Type the call sign for your node. Yes the one you previously wrote down from PTTLink site.

File:Asl call sign.png

Choose option <N4>.

File:Asl n menu n4.png

Choose option <I1>.

File:Asl i menu i1.png

Just say <Ok> to this message.

File:Asl enableing simpleusb.png

Choose option <N5>.

File:Asl n menu n5.png

If your node will be a simplex node type <1>. If your node is a repeater controller type <2>.

File:Asl duplex type.png

Choose option <N6>.

File:Asl n menu n6.png

Type a new password, this will be used to have access from the nodes web site Allmon2, the default password is 'llcgi'.

File:Asl manager password.png

Just say <Ok> to this message.

File:Asl setting new.png

Just say <Ok> to this message.

File:Asl creating basic.png

Choose option <N9>.

File:Asl n menu n9.png

Just say <Ok> to this message.

File:Asl setting repeaters.png

Just say <Ok> to this message.

File:Asl enableing asl.png

Just say <Ok> to this message.

File:Asl setting the node.png

Just say <Ok> to this message.

File:Asl setting node.png

Just say <Ok> to this message.

File:Asl enableing the.png

Just say <Ok> to this message.

File:Asl setting duplex.png

Just say <Ok> to this message.

File:Asl node number.png

Choose option <Back>.

File:Asl n menu back.png

Choose option <AZ>.

File:Asl a menu az.png

Review what you wrote down with what you have configured on your system and press <Enter>.

File:Asl review.png

Choose <Yes> to backup your configuration.

File:Asl backup and save.png

Just say <Ok> to this message.

File:Asl your original.png

Just say <Ok> to this message.

File:Asl new configuration.png

Just say <Ok> to this message.

File:Asl asterisk reload.png

Choose option <Exit>.

File:Asl a menu exit.png

Answer <Yes>, because we already saved our configuration.

File:Asl exit.png

If you want to automatically start your system with this menu answer <Yes>, if not then <No>.

File:Asl select menu at login.png

If you answer was <No>, remember you can come back to this menu typing sudo asl-menu as the following example:

repeater@repeater:~$ sudo asl-menu
File:Asl you may.png

Now your node will reboot to apply all the changes we have done, so say <Ok>.

File:Asl setup is complete.png

PTTLink Audio settings with SimpleUSB

type sudo asl-menu like the example bellow:

repeater@repeater:~$ sudo asl-menu

Choose option <4>.

File:Asl menu 4.png

With option <F>, will trigger PTT few times on your radio for testing, you should also listen a test tone.

Next, with option <2>, you can adjust the audio levels from your radio to your node node with the aim of an on-screen level meter.

With another radio transmit a test tone or voice and type values between 0 and 999 followed by <Enter> to apply them, if you do not set any value and hit <Enter>, you will exit this function keeping the last typed value on RAM.

Next, type option <T>, you can toggle a tone generator to adjust your node to radio audio levels, so type it once to turn it on.

Now typing option <3>, will allow you to adjust the audio from your node to your Tx radio.

To achieve that, you can type values between 0 and 999 and press <Enter> to apply the new value. The system will Tx a test tone for 5 seconds. If you do not set any value and hit <Enter>, you will exit this function keeping the last typed value on RAM.

Do not forget to turn of the tone generator by pressing once again <T>.

Once you are happy with your settings, type <W> and <Enter>.

To exit from this menu type <0> (zero) and hit <Enter>.

PTT and COS polarity settings

If your radio, need PTT and/or COS/CTCSS polarity to be inverted go to the mail PTTLink menu and choose option <6>.

File:Asl menu 6.png

Choose option <I>.

File:Asl configuration menu i.png

You will be logger to a text file where you will need to find and edit some values:

PTT invert:

Search for the line begining with invertptt = and change its value as follows:

0 = Ground to Tramsmit.

1 = Open to Transmit.

File:Asl invertptt.png

COS/CTCSS invert:

Search for the line begining with carrierfrom = and change its value as follows.

Search for the line begining with ctcssfrom = and change its value as follows.

no = No carrier detection at all.

usb = Cor line active Hi.

usbinvert = Cor line active Low.

File:Asl invertcarrier.png

After making your changes type <CTRL> + <X> and then type <Y> followed by <Enter>. You will be back to the previous menu and choose <Back>.

Choose Option <9>.

File:Asl menu 9.png

Choose option <G> to restar PTTLink software and apply changes. Choose <Back>, repeat your audio test if needed.

File:Asl system menu g.png


At this point your node should be up and running.

Port forwarding

You will need to forward port 4569 on your ISP modem. As there are many brands and modems, it is not possible to show a step to step guide.


Allmon2 Setup.

Allmon2 web control.

TBD

DTMF control.

TBD