Search results

...you can log in with a keyboard and monitor or using SSH as in the initial node setup. == Allmon2 Configuration. == ...

...ge your nodes call sign (means on the PTTLink website, not on the physical node), tick the check box that says 'Check this box to change all your callsigns Next, click on '''<Portal>''' and then click on '''<Node Settings>''' ...

*[[LED screens]] - Configuration notes and passwords. *[[Mo-Sys StarTracker]] - Configuration screenshots. ...

...f the image files for you computer system you will use to run your PTTLink node. == Request a Node number == ...

...llowing information is originally from [http://docs.allstarlink.org/drupal/node/12 echolink.conf]. ...would dial *3 followed by 3123456. As you can see we have reserved PTTLink node numbers with a leading 3 for the Echolink number space. ...

...f the image files for you computer system you will use to run your PTTLink node. == Request a Node number == ...

Selecciona la opción '''PTTLink Configuration Edit Menu''' En Node el número del nodo que configuraste en la sección anterior. ...

The Radio Thin Client Module (RTCM) is [http://www.micro-node.com/thin-m1.shtml commercially available] hardware for interfacing radios t The Micro-Node RTCM (and [[VOTER-Hardware | VOTER]]) interfaces are typically used with Al ...

*[[VOTER-Audio | Audio Interfacing and Configuration]] *[[VOTER-GPS | GPS Interfacing and Configuration]] ...

* 01 Micro-Node RTCM board. * 01 Micro-Node RTCM board. ...

...voter.conf</code> file, each stanza (category/instance) is named by the '''node number''' that the clients specified within the stanza are to be associated ...Voter/1999'' in <code>rpt.conf</code>) and is directly associated with the node that opened it. ...

.../code> file is generally going to be located with the rest of the Asterisk configuration files, in <code>/etc/asterisk</code>. ...pical voting repeater scenario, the ''instance'' would typically be the '''node number''', and all the clients would be the transmitter client and all the ...

.../code> file is generally going to be located with the rest of the Asterisk configuration files, in <code>/etc/asterisk</code>. ...pical voting repeater scenario, the ''instance'' would typically be the '''node number''', and all the clients would be the transmitter client and all the ...

= Micro-Node RTCM Clock Issue = ...cted a small run of the RTCM's. The issue was eventually resolved by Micro-Node, but we'll document it here just for record keeping. ...

...repeater/node coverage you only need a TETRA radio. I there is no repeater/node in your area you can setup one an link it to the TETRA Mexico network. * GPS>LIP Configuration/Destination ISSI = 9999 ...

...o a Motorola Quantar (Quantro should be similar). These are just the basic configuration steps, based on the following scenario: ...m/motorola/quantar/qim/part-14-station-configuration.pdf Part 14 - Station Configuration], you will find a section called "Fast Keyup Feature". ...

Hasta arriba de la página, da click en '''<Portal>''' y luego en '''<Node Settings>'''. [[File:Ptt site node settings.png|none|thumb|604x604px]] ...

...through-hole VOTER, this page is for you. If you have an [http://www.micro-node.com/thin-m1.shtml RTCM], then you will want to reference the [http://173.24 The Micro-Node RTCM (and [[VOTER-Hardware | VOTER]]) interfaces are typically used with Al ...

You will still need to set the data and PPS polarity, and baud rate in the configuration menus to get everything to work. Beware when buying newer Garmin GPS's to use with the Micro-Node RTCM. ...

...lots of those still surplus). It would appear that there is a valid clock configuration for the dsPIC that '''would''' allow this clock signal to be used, and stil ...m1.shtml Micro-Node International] and marketed as their [http://www.micro-node.com/thin-m1.shtml Radio Thin Client Module (RTCM)]. The RTCM is effectively ...